The Insulation Man

Based on our email, this is one of the most popular questions homeowners ask before buying insulation. The answer is that the 'best' type of insulation depends on:

• how much insulation is needed,
• the accessibility of the insulation location,
• the space available for the insulation,
• local availability and price of insulation, and
• other considerations unique to each purchaser.

What Is an R-Value?

Insulation is rated in terms of thermal resistance, called R-value, which indicates the resistance to heat flow. The higher the R-value, the greater the insulating effectiveness. The R-value of thermal insulation depends on the type of material, its thickness, and its density. In calculating the R-value of a multi-layered installation, the R-values of the individual layers are added.

The effectiveness of an insulated ceiling, wall or floor depends on how and where the insulation is installed.

• Insulation which is compressed will not give you its full rated R-value. This can happen if you add denser insulation on top of lighter insulation in an attic. It also happens if you place batts rated for one thickness into a thinner cavity, such as placing R-19 insulation rated for 6 1/4 inches into a 5 1/2 inch wall cavity.
• Insulation placed between joists, rafters, and studs does not retard heat flow through those joists or studs. This heat flow is called thermal bridging. So, the overall R-value of a wall or ceiling will be somewhat different from the R-value of the insulation itself. That is why it is important that attic insulation cover the tops of the joists and that is also why we often recommend the use of insulative sheathing on walls. The short-circuiting through metal framing is much greater than that through wood-framed walls; sometimes the insulated metal wall's overall R-value can be as low as half the insulation's R-value.

Reading the Label

No matter what kind of insulation you buy, check the information on the product label to make sure that the product is suitable for the intended application. To protect consumers, the Federal Trade Commission has very clear rules about the R-value label that must be placed on all residential insulation products, whether they are installed by professionals, or whether they are purchased at a local supply store. These labels include a clearly stated R-value and information about health, safety, and fire-hazard issues. Take time to read the label BEFORE installing the insulation. Insist that any contractor installing insulation provide the product labels from EACH package (which will also tell you how many packages were used). Many special products have been developed to give higher R-values with less thickness. On the other hand, some materials require a greater initial thickness to offset eventual settling or to ensure that you get the rated R-value under a range of temperature conditions.

Insulation Product Types

Some types of insulation require professional installation, and others you can install yourself. You should consider the several forms of insulation available, their R-values, and the thickness needed. The type of insulation you use will be determined by the nature of the spaces in the house that you plan to insulate. For example, since you cannot conveniently "pour" insulation into an overhead space, blankets, spray-foam, board products, or reflective systems are used between the joists of an unfinished basement ceiling. The most economical way to fill closed cavities in finished walls is with blown-in insulation applied with pneumatic equipment or with sprayed-in-place foam insulation.

The different forms of insulation can be used together. For example, you can add batt or roll insulation over loose-fill insulation, or vice-versa. Usually, material of higher density (weight per unit volume) should not be placed on top of lower density insulation that is easily compressed. Doing so will reduce the thickness of the material underneath and thereby lower its R-value. There is one exception to this general rule: When attic temperatures drop below 0°F, some low-density, fiberglass, loose-fill insulation installations may allow air to circulate between the top of your ceiling and the attic, decreasing the effectiveness of the insulation. You can eliminate this air circulation by covering the low-density, loose-fill insulation with a blanket insulation product or with a higher density loose-fill insulation.

Blankets, in the form of batts or rolls, are flexible products made from mineral fibers, including fiberglass or rock wool. They are available in widths suited to standard spacings of wall studs and attic or floor joists. They must be hand-cut and trimmed to fit wherever the joist spacing is non-standard (such as near windows, doors, or corners), or where there are obstructions in the walls (such as wires, electrical outlet boxes, or pipes). Batts can be installed by homeowners or professionals. They are available with or without vapor-retarder facings. Batts with a special flame-resistant facing are available in various widths for basement walls where the insulation will be left exposed.

Blown-in loose-fill insulation includes cellulose, fiberglass, or rock wool in the form of loose fibers or fiber pellets that are blown using pneumatic equipment, usually by professional installers. This form of insulation can be used in wall cavities. It is also appropriate for unfinished attic floors, for irregularly shaped areas, and for filling in around obstructions.

In the open wall cavities of a new house, cellulose and fiberglass fibers can also be sprayed after mixing the fibers with an adhesive or foam to make them resistant to settling.

Foam insulation can be applied by a professional using special equipment to meter, mix, and spray the foam into place. Polyisocyanurate and polyurethane foam insulation can be produced in two forms: open-cell and closed-cell. In general, open-celled foam allows water vapor to move through the material more easily than closed-cell foam. However, open-celled foams usually have a lower R-value for a given thickness compared to closed-cell foams. So, some of the closed-cell foams are able to provide a greater R-value where space is limited.

Rigid insulation is made from fibrous materials or plastic foams and is produced in board-like forms and molded pipe coverings. These provide full coverage with few heat loss paths and are often able to provide a greater R-value where space is limited. Such boards may be faced with a reflective foil that reduces heat flow when next to an air space. Rigid insulation is often used for foundations and as an insulative wall sheathing.

Reflective insulation systems are fabricated from aluminum foils with a variety of backings such as kraft paper, plastic film, polyethylene bubbles, or cardboard. The resistance to heat flow depends on the heat flow direction, and this type of insulation is most effective in reducing downward heat flow. Reflective systems are typically located between roof rafters, floor joists, or wall studs. If a single reflective surface is used alone and faces an open space, such as an attic, it is called a radiant barrier. Radiant barriers are installed in buildings to reduce summer heat gain and winter heat loss. In new buildings, you can select foil-faced wood products for your roof sheathing (installed with the foil facing down into the attic) or other locations to provide the radiant barrier as an integral part of the structure. For existing buildings, the radiant barrier is typically fastened across the bottom of joists, as shown in this drawing. All radiant barriers must have a low emittance (0.1 or less) and high reflectance (0.9 or more).

   

         We Vacuum out contaminated insulation

                         Click for video

The Insulation Man The Insulation Man The Insulation Man The Insulation Man The Insulation Man The Insulation Man
The Insulation Man services Virginia Beach, Chesapeake, Norfolk, Portsmouth, Suffolk, Hampton,Newport News Thermal insulation is a material having air-filled cells or voids, or heat-reflective surfaces, which retard the transfer of heat to cold. Acoustical insulation retards the transmission of sound. Pest control insulation, while performing the other functions of thermal and acoustical, is labeled to control listed insects. By Federal law, such insulation (and the manufacturing plant) must be registered with the US EPA, and carry an EPA-approved label. Additionally, the product must be registered with the pest control authorities in each state in which it is sold or manufactured. Because T·A·P is an EPA-labeled pesticide, in many states only a licensed PMP may sell the insulation.
Why choose The Insulation Man ? The Insulation Man is a division of Universal Pest & Termite who has been servicing the Tidewater area for over 10 years. Universal has been recognized as one of the fastest growing service based companies in Virginia. This backing allows us to own all of our own equipment without having to rent old, out dated equipment and jeopardizing the quality of your job. What services does The Insulation Man perform? -  We vacuum out old contaminated insulation and dispose of it in a clean manner - We treat attic and crawl space areas with a liquid disinfectant, sanitizer, virucide - We clean out debri from crawl space areas that hold rodents and wildlife - We re-install T.A.P insulation in attic to the R-30 code - We install bat insulation in the crawl space sub-floor - We install new foundation vents to keep out unwanted rodents and wildlife - We seal outside openings to keep out rodents and wildlife - If needed Universal Pest & Termite can perform pest services - Mold testing and treatments    Mold in attic              Access Cover  - We install access covers. Keep the heat in and the rodents out.   Contact our office for a FREE INSULATION INSPECTION 502-0200
Why should you have you attic cleaned and disinfected?         [ rodent urine ] T·A·P saves energy. T·A·P saves money by decreasing energy bills. It keeps homes cool in summer and warm in winter for less money: Comfortable year-round. Because T·A·P is denser than fiberglass insulation, air does not move through it well, so it resists heat transfer by convection, as well as conduction and radiation. And since there aren’t the leaks and drafts associated with ordinary insulation, mechanical systems don’t work as hard and can be down-sized, further saving money. Areas in the home maintain more uniform temperatures between floors and ceilings, upstairs and downstairs, even next to exterior walls. Comfort. Conservation.
All-Natural, Permanent, and Environmentally Friendly, too. T·A·P is Green! Well, not in color, but T·A·P is permanent, made from all-natural boric acid and recycled newsprint; thus while you’re saving energy, you’re also conserving landfill space.   Click for video
Most houses are cellulose (made from wood and forest products). T·A·P contains a fire-retardant chemical that actually makes homes safer in case of fire. Ordinary fiberglass insulation can melt, creating a chimney-like effect in a wall. T·A·P, with its fire-retardant characteristics, forms a charred surface barrier which limits the spread of fire.
Blown-in T·A·P forms a perfect fit in your wall or attic when applied, seeking nooks and crannies, filling the entire cavity. As every homebuilder knows, stud cavities are not uniform in size; thus, gaps and voids form when uniformly sized batts are used. Unlike fiberglass batts,T·A·P is never cut on the jobsite, or stuffed into the cavity to fit behind pipes and conduits, reducing the R-Value. With T·A·P, the R-Value stays in the insulation! And that means the added value stays in the home and becomes a permanent benefit you can sell to the next owners. Contact our office for a free insulation assessment  502-0200 The Insulation Man installs T.A.P. insulation, the leading blown insulation product with a built in pest guard product blended in. This cellulose insulation is fire resistant and fits your attic perfectly. We also vacuum old insulation out and bag it using our custom vacuum system which allows the process to be performed with little to no mess. Attic insulation, crawl space insulation,sub floor insulation basement insulation, blown in insulation, bat insulation.We install insulation in Virginia Beach, Chesapeake,Norfolk,Portsmouth,Hampton,Suffolk and Newport News.Ther are other insulation companies in the area but only one Insulation Man.